CETME
The name
CETME is an acronym for
Centro de Estudios Técnicos de Materiales Especiales, a Spanish government design and development establishment. The CETME rifle, which was initially trialed with other calibers, but eventually chambered for
7.62x51mm NATO caliber (aka .308 Winchester), was designed primarily by the German engineer,
Ludwig Vorgrimmler, who based his model on a late WWII German prototype
assault rifle, the experimental
StG-45(m). The StG-45 used a roller-delayed blowback mechanism somewhat similar to the roller-locking system patented by the
Edward Stecke in the
1930s in
Poland and used in the
MG42. The MG42 locking system actual locks completely and requires a moving barrel that travels backwards to unlock, compared to the STG45 system that never completely locks and does not require a moving barrel.
Manufactured in
Spain from
1957, the CETME served as a blueprint for the German
Heckler & Koch G3 series of
battle rifles. The CETME features
roller-delayed blowback operation, which it shares with many German weapons. The CETME rifle was manufactured in five models, the A, B, C, L , LC and LV models. The primary difference in the three first models is the absence of bipod and less weight C model, with more wood. The L series was the "light", moderm 5.56 NATO assault rifles with composite materials, the LC was the short version of it, and the LV was a improved, and last version of Cetme L.
CETME also designed the CETME C2 a 9mm advanced Sterling-like sub-machine gun, and the AMELI (AMEtralladora LIgera) a light machine gun in 5.56 NATO.
The CETME, like its descendant, the
Heckler & Koch G3 is of modular construction, based around a stamped steel receiver, a pressed in barrel, and a detachable '
trigger group' which encompasses the handgrip, trigger, and fire selector mechanism. Its folding charging handle is mounted on the left side of the weapon, above the barrel and forend of the stock. The CETME does not have a bolt hold-open device; when the final cartridge is fired, the bolt does not remain open, and thus the rifleman cannot tell if he has expended his ammunition. Not using such a device allowed the CETME design to contain fewer moving parts and may make it more reliable. To signal when a magazine is near empty, the final rounds can instead be loaded with tracer rounds.
The magazines are made of steel. In military service the CETME's magazine was typically of twenty-round capacity, though five-round magazines were manufactured for garrison duty and aftermarket five-round magazines are available on the civilian market due to restrictions on magazine size in hunting rifles in the US. The magazine was removed via a "flapper" behind the magazine and forward of the trigger guard. This was pushed forward, dropping the magazine. Magazines from the H&K G3 can also be used in the CETME, though minor modifications may be needed.
Stripping of the weapon is achieved by pushing two small pins from the buttstock, removing the buttstock and recoil spring, pulling the trigger pack down, and pulling back the charging handle to push the bolt out of the rifle.
Century International Arms, Inc. formerly of Fairfax, Vermont, then Georgia, Vermont, and currently of Delray Beach, Florida, imported the majority of CETME rifles into the United States. As their manual says, "The Cetme Rifle is built using genuine Cetme parts and a U.S. manufactured receiver. The Cetme conforms to B.A.T.F. requirements. It is semi-automatic only." Specifically, in order to import an assault rifle into the United States, the fully automatic receiver must be destroyed, and a certain number of US manufactured parts must be substituted. Specifically, from a list of twenty parts, no more than ten may be of foreign manufacture (see BATFE's sec.922r). In the case of the Century CETME, the receiver, trigger group, muzzle attachments and plastic furniture are of US manufacture, so the Century CETME complies with regulations. In the 1960's the company MARS imported the semi-auto CETME into the US for the sporting market, with original spanish receiver parts. These early import CETMEs are quite rare, and robust, and fetch a price approaching 5-6 times that of a Century CETME.
*
WWW.CETMERIFLES.COM*
CETME information page*
Buddy Hinton Collection / CETME*
CETME For Dummies webpage*
CETME Firing Demonstration Video*
CETME Model C Manual*
Century Arms CETME Manual*
Code of (US) Federal Regulations, Title 27 (See sections 447, 478, and 479)
*
Legal Implications of building a gun from a parts set or kit
